Item Code Item Name
CASE C001 (Discon) to CASE-022812
CASE-020303 (Discon 2020) to CASE-022824
CASE-020304 Vacuum Pump
CASE-020305 Water Flow Sensor
CASE-020308 Motor
CASE-020309 Water A Tube
CASE-020310 Water B Tube
CASE-020312 Power Cord
CASE-020403 Control PCB
CASE-020406 Air regulator
CASE-020409 Vacuum Valve
CASE-020410 Pressure Valve
CASE-020411 Ejector-P Valve
CASE-020412 Ejector-V Valve
CASE-020414 Heater PCB
CASE-020415 Photo Sensor Assembly
CASE-020418 Ejector Filter
CASE-020501 Vacuum Filter (Compressed Air Filter)
CASE-020601 Ceramic Plate
CASE-020602 Retort
CASE-020604 Casting Stand
CASE-020607 Tube (Retort Hold Pipe)
CASE-020701 View Glass
CASE-020706 Window Glass
CASE-020707 Window O Ring
CASE-020795 Ring Holder
CASE-020804 Chiller P.C.B
CASE-020806 Power Converter
CASE-020807 Water Funnel
CASE-022801 Crucible Stand
CASE-022810 Carbon Crucible (S)
CASE-022811 Carbon Crucible (L)
CASE-022812 Ceramic Crucible
CASE-022813 Melting Alloy Outlet (Pourer for Crucible)
CASE-022824 Vacuum Filter L
CASE-C000 Cascom SE (machine）
CASE-C012 Retort Lower Stand
NC7-021　 Casting Flux (SF-50)
Chiller Installation
  1. Connect the chiller to Cascom SE as shown below. (Picture from Chiller Instruction page 5)
  2. Remove the white cap of water inlet and place the water funnel
  3. Pour coolant through the water funnel
  4. Add water to the F line
  5. Remove the water funnel
  6. Place the white cap back on

After installing the chiller with Cascom SE, turn on the power of the Cascom SE and wait for 10 min so coolant/water circulates into the unit completely.

Water Overheating

□ H.  indicates that Chiller water temperature is overheating. Wait for 10min to use the unit.

Cautions
Signs Causes   Recommended Solutions
ot Time over of induction. Carrying time of high frequency current reaches the limit. The limit is 5 minutes.*Press any button to return to normal display.
Ft Abnormal cooling fan filter. Cooling fan unable to work properly. Clean the filter located at the bottom of the unit. In case of no improvement, the fan must be replaced.*Press any button to return to normal display.
oH Water overheating. Coolant/water in the chiller is overheating. Wait for 10 min to use the unit. When the sign is displayed multiple times, clean the chiller filter.* Excessively high room temperature also causes this caution sign.

 

Error Signs
No.’s Causes Recommended Solutions
00 Optional chiller is abnormal. Check the connection of outlet and signal terminals.
01 Water is leaking in the unit. Stop using the unit immediately. Contact our technical support team for repair.
02 Water is leaking in the optional.chiller. Stop using the chiller immediately. Contact our technical support team for repair.*Poor connection of the signal terminal may cause this error.
03 Chiller water is below required amount. Check the amount of water/chiller in the chiller. Add more if necessary.*Poor connection of signal terminals may cause this error.
04 Chiller water is not flowing. Check the hose and connection between the chiller and the unit.* Poor connection of the signal terminal may cause the error.
05 Muffle chamber is unable to invert to the casting position. Check if any objects interfere with inverting of the chamber.
06 Muffle chamber is unable to invert to the melting position. Check if any objects interfere with inverting of the chamber.
10 Over-Current of high frequency power. Unable to measure power frequency. Abnormal or excessively loud noise may cause this error. If the error sign is displayed often, contact our technical support team for repair.
11 Protective circuit of high frequency power is operated. Abnormal or excessively loud noise may cause this error. If the error sign is displayed often, contact our technical support team for repair.
12 High frequency is not output. High frequency power may malfunction. Contact our technical support team.
14 Unable to measure power frequency. High frequency power may malfunction. Contact our technical support team.
15 Power supply voltage is out of range. The unit operates only with single-phase, 220-240V and 20A. Check power supply voltage and allowable current.
16 Memory data is damaged. Abnormal or excessively loud noise may cause data damage or change memory data. Contact our technical support team.
17 Control board is abnormal. If the error sign is displayed multiple times, contact our technical support team for repair.
18 High frequency power board is abnormal. If the error sign is displayed multiple times, contact our technical support team for repair.
Choosing the Right Crucible

Ceramic Crucible is used for Semi-Precious alloy that contains Palladium for more than 30% and for Non-Precious alloy such as Nickel-Chrome and Cobalt-Chrome alloy. Carbon Crucible is used for precious alloys such as Gold and Silver based metal.

Burnout

Burnout process is one of the most important aspects of the casting with Cascom SE. In the case of insufficient burnout, you might experience short casting.

1. Phosphate for Crown & Bridge Gold

  • Burnout w/ 1560°F (850°C) minimum of 1 hour and 20min. Longer is better.

2. Phosphate for Porcelain Fused Metal

  • Burnout w/ 1650°F (900°C) over 1 hour. Longer is better.

 

Air Pressure

Cascom SE requires 100psi to 145psi of pressurized air from the compressor. Insufficient air pressure is one of the most common reasons for short cast. If the distanse between the unit and the air compressor is far, Cascom SE might get less than 100psi even if the regulator of the compressor is showing 100psi.

Argon Gas

When you cast metal that contains Palladium for more than 30% or Non-Precious metal, you must use Argon Gas. Argon Gas prevents oxidation and it helps to achieve clean casting results. Lack of argon gas causes alloy to not flow into the ring smoothly.

Nickel-Chrome Alloy

The most common Nickel-Chrome alloy miscast is metal not flowing into the ring due to overheating. When you overheat Nickel-Chrome alloy, it gets very sticky and does not drop smoothly to the ring. In this case, cast timing is very critical and you must press the [CAST] button earlier than usual.

Instructions
  1. How to cast Precious/Semi-precious metal (PALLADIUM LESS THAN 30%) – PDF
  2. How to cast Semi/Non-precious metal (PALLADIUM MORE THAN 30%) – PDF
Other Products

Neo Super Cascom
Zircom
007 PL
Wax Master II
Master Plus

For more information, please contact us.